BMW 7 Owners & Service Manuals

BMW 7 Series: Driver profiles- Setting up a PIN

A driver profile with recognition cannot be activated without vehicle key. In this case, a PIN can be set up to activate the driver profile.

Non-ConnectedDrive countries: If a PIN was not set up or the PIN is not known, the driver's profile cannot be activated.

ConnectedDrive countries: If a PIN was not set up or the PIN is not known, the driver's profile can be activated with the access data of the corresponding ConnectedDrive account.

Via iDrive:

  1. "CAR"
  2. "Driver profiles"
  3. Move the Controller to the right.

    As an alternative for Steps 1 to 3, the profile image can be tapped in the top status bar.

  4. "Driver recognition"
  5. "using PIN"

Changing/canceling the recognition function

If another vehicle key is assigned to a driver profile, the current assignment must be canceled first.

Via iDrive:

  1. "CAR"
  2.  "Driver profiles"
  3. Move the Controller to the right.

    As an alternative for Steps 1 to 3, the profile image can be tapped in the top status bar.

  4. "Driver recognition"
  5. "with vehicle key"
  6. "Activate linkage"

When the vehicle and vehicle key will be handed over, such as for maintenance, carry out the following steps first:

  • Setting up PIN.
  • Canceling recognition using the vehicle key.
  • Switching to the guest profile.

The handed over vehicle key can then no longer be used to access the personal driver profile.

Selecting a driver profile

Depending on the recognition setting, the driver profile will be selected automatically.

If the guest profile is active, the driver profile will be selected on the Welcome screen or via iDrive: A PIN may have to be entered.

  1. "CAR"
  2. "Driver profiles" As an alternative for Steps 1 and 2, the profile image can be tapped in the top status bar.
  3. Select driver profile.
  4. "OK"

All settings stored in the selected driver profile are automatically applied.

Switching synchronization with the ConnectedDrive account on/off

ConnectedDrive countries: The settings stored in the driver's profile are synchronized with the personal ConnectedDrive account. This means that it is possible to use the personal settings in other BMW vehicles with ConnectedDrive access as well, if this function is supported.

The synchronization with the ConnectedDrive account is enabled when a driver profile is created or via iDrive:

  1. "CAR"
  2. "Driver profiles"
  3. Move the Controller to the right.

    As an alternative for Steps 1 to 3, the profile image can be tapped in the top status bar.

  4.  "Settings"
  5. "Synchronize driver profile"
  6. "Synchronize driver profile"

    READ NEXT:

     Driver profiles- Renaming a driver profile

    Countries in which ConnectedDrive is not available: The name that was assigned when the driver profile was set up can be changed via iDrive: "CAR" "Driver profiles" As an alternative for Steps

     Connections

     Connecting mobile devices to the vehicle

    Vehicle features and options This chapter describes all standard, country-specific and optional features offered with the series. It also describes features and functions that are not necessarily ava

    SEE MORE:

     Instructions For Disconnecting And Connecting Battery

    Observe SAFETY INSTRUCTIONS FOR HANDLING VEHICLE BATTERY. Before disconnecting battery Turn off the ignition and other electrical loads/consumers to prevent sparking when reconnecting. NOTE: If the ignition is not turned off when the battery is disconnected, fault memories may be set in some contr

     Replacing Led For Front Door Trim Panel Light (Left Or Right)

    Necessary preliminary tasks Remove FRONT LEFT DOOR TRIM PANEL Unlock LED for front door trim panel (1) from holder (2). Detach LED for front door trim panel (1). Installation Make sure LED for front door trim panel (1) is correctly seated in holder (2). Fig. 107: Identifying LED For Front Door

    © 2019-2024 Copyright www.bmw7g11.com