BMW 7 Owners & Service Manuals
BMW 7 Series (F01/F02) 2008-2015 Service Manual / General Electrical System / Wiring Harness / Installing Repair Cable For Left Side View Camera

BMW 7 Series: Installing Repair Cable For Left Side View Camera

Read and comply with notes on HANDLING WIRING HARNESSES AND WIRING.

NOTE: Work is shown on the F01 by way of example. There may be differences in detail in the case of other vehicle types and equipment specifications.

Necessary preliminary tasks:

  • Remove FRONT WHEEL ARCH COVER (FRONT SECTION)
  • Remove SEAL MOUNTING FOR ENGINE COMPARTMENT LID
  • Remove FOOTWELL SIDE TRIM PANEL ON A-PILLAR, LEFT
  • Preliminary work is described in REMOVING CONTROL UNIT FOR TOP-/REAR-/SIDE- VIEW CAMERA , but do not remove the control unit
  • Remove FRONT SEAT ON THE DRIVER'S SIDE
  • Remove backrest side section on rear seat backrest
  • Remove BACKREST
  • Remove BOTTOM TRIM PANEL FOR DOOR POST

NOTE: Required preliminary may vary according to vehicle type and equipment.

Lever expanding rivets (1) out of cover (2).

Remove cover (2).

Installation note: If necessary, replace damaged expanding rivet.

Make sure holders (3) are correctly seated.

Wiring Harness
Fig. 6: Identifying Rivets, Cover, And Holders

Unlock the lock (1) in direction of arrow with suitable tool.

IMPORTANT: Risk of damage!

Unlock the lock (3) carefully with a suitable tool. Pull connector housing (4) of line (2) in direction of arrow.

Installation note: Pay attention to encoding (5)!

Wiring Harness
Fig. 7: Identifying Lock And Connector Housing

Connect repair cable (2) to Side View camera (1).

Lay repair cable (2) in direction of arrow along wiring harness (3) and secure at points marked with an arrow.

Wiring Harness
Fig. 8: Identifying Side View Camera, Wiring Harness, And Repair Cable

Loosen screws from expansion tank (5) and set expansion tank to one side.

Lay repair cable (1) in direction of arrow along wiring harness (4) and secure at points marked with an arrow.

IMPORTANT: Risk of damage to wiring harness.

Carefully feed repair cable (1) through grommet (2).

After repair cable (1) has been fed through and secured, mask grommet (2) at point (3) with suitable adhesive tape.

Wiring Harness
Fig. 9: Feeding Repair Cable Through Grommet

IMPORTANT: Risk of damage to wiring harness.

Break through rubber grommet (3) at point (4) using a suitable tool.

Lay repair cable (2) in direction of arrow along wiring harness (1) and secure at points marked with an arrow.

Feed through repair cable (2) at point (4) in driver's footwell.

IMPORTANT: To prevent moisture from entering the passenger compartment, seal opening (4) on the outside, using suitable means!

Wiring Harness
Fig. 10: Routing Repair Cable To Driver's Footwell

Carefully lay carpet (4) to one side. Lay repair cable (2) from entry point (1) in direction of arrow along wiring harness (3) below carpet (4) and secure to wiring harness (3) at suitable distances.

Wiring Harness
Fig. 11: Routing Repair Cable From Entry Point Along Wiring Harness Below Carpet

Carefully lay carpet to one side. Lay repair cable (2) in direction of arrow along wiring harness up to all-round vision camera control unit (1) secure to wiring harness at suitable distances.

Wiring Harness
Fig. 12: Routing Repair Cable Up To Control Unit

Assemble repair cable. Connect repair cable to slot (2) of all-round vision camera control unit (3).

NOTE: Lay and secure and overlengths of repair cable below wheel arch trim panel in left luggage compartment.

After successful completion of function check , detach start and end of faulty cable at first mounting point.

Wiring Harness
Fig. 13: Connecting Repair Cable To Control Unit

    READ NEXT:

     Installing Repair Cable For Reversing Camera

    Read and comply with notes on HANDLING WIRING HARNESSES AND WIRING. NOTE: Work is shown on the F01 by way of example. There may be differences in detail in the case of other vehicle types and equipme

     Notes On Handling Wiring Harnesses And Cables

    The following applies in general To avoid damage, observe the following instructions: Avoid compressive and tensile loads To ensure professional repairs, perform repair work only with BMW-approve

     Auxiliary Cable

    SEE MORE:

     Removing And Installing/Replacing Oil Pump (N63)

    Notes IMPORTANT: All adjusting procedures on the chain drive must be observed. A timing chain which is tensioned too tautly can cause noises in the chain drive. A timing chain that is too slack can cause the timing chain to jump. Risk of damage in oil pump drive. Necessary preliminary work DRAI

     Functions

    Bluetooth Pairing (pairing wizard) The pairing wizard presents the step-by-step instructions for the entire pairing process via the Central Information Display (CID). Detailed help texts and instructions for further assistance are available in case pairing is not successful. This pairing wizard f

    © 2019-2024 Copyright www.bmw7g11.com