BMW 7 Owners & Service Manuals
BMW 7 Series (G11/G12) 2015-2022 Owners Manual / Controls / Driving / Steptronic transmission- Engaging selector lever positions

BMW 7 Series: Steptronic transmission- Engaging selector lever positions

General information

To prevent the vehicle from creeping after you select a drive mode, maintain pressure on the brake pedal until you are ready to start.

Functional requirements

Only when the drive-ready state is switched on and the brake pedal is depressed is it possible to change from selector lever position P to another selector lever position.

The selection lever position P cannot be changed until all technical requirements are met.

Engaging selector lever position D, N, R

A selector lever lock prevents the following faulty operation:

  • Unintentional shifting into selector lever position R.
  • Unintentional shifting from selector lever position P into another selector lever position.
  1. Fasten driver's safety belt.
  2. Press and hold the button to release the selector lever lock.

Engaging selector lever positions


  1. Push the selector lever in the desired direction, past a resistance point, if needed. The selector lever automatically returns to the center position when released.

Engaging selector lever positions


Engaging selector lever position P

Engaging selector lever position P


Press button P.

Rolling or pushing the vehicle

General information

In some situations, the vehicle is to roll without its own power for a short distance, for instance in a car wash, or be pushed.

Engaging selector lever position N

  1. Switch on drive-ready state while pressing on the brake pedal.
  2. If necessary, release the parking brake.
  3. If necessary, switch off Automatic Hold. Automatic Hold, refer to page
  4. Depress the brake pedal.
  5. Touch the selector lever lock and engage selector lever position N.
  6. Switch off drive-ready state.

In this way, standby state remains switched on, and a Check Control message is displayed.

The vehicle can roll.

NOTICE


Selector lever position P is automatically engaged when standby state is switched off.

There is a risk of damage to property. Do not switch standby state off in vehicle washes.

Selector lever position P is engaged automatically after approximately 35 minutes.

If there is a malfunction, you may not be able to change the selector lever position.

Electronically unlock the transmission lock, if needed.

Kickdown

Kickdown is used to achieve maximum driving performance.

Step on the accelerator pedal beyond the resistance point at the full throttle position.

Sport program M/S

Concept

The shifting points and shifting times in the Sport program are designed for a sportier driving style. The transmission, for instance shifts up later and the shifting times are shorter.

Activating the Sport program

Activating the Sport program


Press the selector lever to the left from selector lever position D.

The engaged gear is displayed in the instrument cluster, for instance S1.

The sport program of the transmission is activated.

Ending the Sport program

Push the selector lever to the right.

D is displayed in the instrument cluster.

    READ NEXT:

     Steptronic transmission- Manual mode M/S

    Concept Manual gear-shifting is possible in manual mode. Activating manual mode Press the selector lever to the left from selector lever position D, arrow 1. Push the selector lever forward or

     Steptronic transmission- Launch Control

    Concept Launch Control enables optimum acceleration on surfaces with good traction under dry surrounding conditions. General information The use of Launch Control causes premature component wear since

     Displays

    SEE MORE:

     Installing Servodrive

    Installation: If necessary, align shaft of flap(s) to be actuated to position of servodrive to be installed. Fig. 4: Identifying Servodrive Position OVERVIEW OF ACTUATOR DRIVES ON HEATER/AIR CONDITIONER Fig. 5: Identifying Actuator Drives On Heater/Air Conditioner Components Actuator drive, ven

     Removing And Installing Complete Independent Heater

    WARNING: Risk of scalding! Only perform the following repair work on an engine that has cooled down. Follow Notes for Repair Work on Cooling System. NOTE: Clamp off coolant hoses on independent heater. Recycling Fuel escapes when fuel line is detached. Have a suitable collecting vessel ready. Cat

    © 2019-2024 Copyright www.bmw7g11.com