BMW 7 Owners & Service Manuals
BMW 7 Series (F01/F02) 2008-2015 Service Manual / Integrated Suspension Systems / Connecting Lines / Removing And Installing/Renewing Dynamic Drive In The Wheel Arch

BMW 7 Series: Removing And Installing/Renewing Dynamic Drive In The Wheel Arch

Notes

WARNING: DANGER OF POISONING if oil is ingested/absorbed through the skin! RISK OF INJURY if oil comes into contact with eyes and skin!

IMPORTANT: Adhere to the utmost cleanliness. Do not allow any dirt to enter the hydraulic system.

Do not draw off hydraulic fluid (risk of contamination).

Close off line connections with seal plug. 32 1 270

Recycling

Catch and dispose of hydraulic fluid in a suitable expansion tank.

Necessary preliminary work

  • Remove front right wheel arch cover.
  • Remove UNDERBODY PROTECTION
  • Remove right STEERING ASSEMBLY COVER
  • Release front right UNDERBODY PANELLING

IMPORTANT: Pressure lines must be closed off with suitable seal plugs 32 1 270 immediately after removal!

Release screw (1) for return line.

Connecting Lines
Fig. 61: Identifying Return Line Mounting Screw

Installation note:

IMPORTANT: When tightening the screw connection (1), apply counter support with wrench (3) at the line (2)! Non-compliance will result in damage to the line (2)! Tightening torque 37 13 12AZ.

Connecting Lines
Fig. 62: Applying Counter Support With Wrench During Tightening Screw Connection

Release line clips (1) and (2) from front axle support.

Connecting Lines
Fig. 63: Identifying Front Axle Support Line Clips

Release screw (1) in area of lower wishbone.

Tightening torque 37 13 8AZ.

Connecting Lines
Fig. 64: Identifying Screw In Lower Wishbone Area

IMPORTANT: When assembling, make sure that in succession only the seal plugs of the line to be fitted are removed.

When fitting lines, do not tilt connectors (sealing rings!) and connect fully before screwing.

Do not replace sealing rings on hydraulic lines.

Replace affected line if sealing ring is damaged.

After installation

  • Fill and bleed HYDRAULIC SYSTEM
  • Check line connections for leak tightness
  • Perform INITIAL OPERATION OF ARS

    READ NEXT:

     Removing And Installing/Renewing Pressure Line For VA1 Swivel Motor

    Notes WARNING: DANGER OF POISONING if oil is ingested/absorbed through the skin! RISK OF INJURY if oil comes into contact with eyes and skin! IMPORTANT: Adhere to the utmost cleanliness. Do not allow

     Removing And Installing/Renewing Pressure Lines For Valve Block (Short)

    Notes WARNING: DANGER OF POISONING if oil is ingested/absorbed through the skin! RISK OF INJURY if oil comes into contact with eyes and skin! IMPORTANT: Adhere to the utmost cleanliness. Do not allow

     Removing And Installing/Replacing Pressure Line For Valve Block VA1

    Notes WARNING: DANGER OF POISONING if oil is ingested/absorbed through the skin! RISK OF INJURY if oil comes into contact with eyes and skin! IMPORTANT: Adhere to the utmost cleanliness. Do not allow

    SEE MORE:

     Instructions For Adapting Adjustment Unit For Reversing Camera (CORGHI KDS Quick-Action Clamp)

    The following operations should only be carried out when using the tool kit for calibrating the reversing camera for the first time. NOTE: The operation is described for the left-hand side; proceed in the same way for the right-hand side. Remove support plate (1) from spindle (2). Replace spindle

     System Overview

    Anti-theft System Circuit Diagram Fig. 34: Anti-Theft System Circuit Diagram COMPONENTS DESCRIPTION CHART Hood switch Car Access System 4 (CAS4) Anti-theft system (DWA) LED Junction Box electronics (JB) Front power distribution box Door contact, passenger's door Door contact, rear passenger

    © 2019-2025 Copyright www.bmw7g11.com