BMW 7 Owners & Service Manuals
BMW 7 Series (F01/F02) 2008-2015 Service Manual / General Electrical System / Switch / Replacing Roof Switch Cluster (Roof Function Center)

BMW 7 Series: Replacing Roof Switch Cluster (Roof Function Center)

IMPORTANT: Only new parts may be used for replacement (repair kit)*.

*Sourcing reference: BMW Parts Catalogue

IMPORTANT: Read and comply with notes on protection against electrostatic damage (ESD PROTECTION).

Necessary preliminary work

  • Remove ROOF SWITCH CLUSTER

Secure switch unit (1) to cover (2).

Switch
Fig. 262: Identifying Switch Unit On Cover

Clip light unit (1) into cover (2).

Switch
Fig. 263: Identifying Light Unit With Cover

Insert retaining lugs on switching mat (1) correctly into designated guides on board (2).

Connect USIS sensor plug connections (3) to board (2).

NOTE: USIS sensors (3) are used only when anti-theft alarm system is fitted.

Switch
Fig. 264: Identifying Switching Mat, USIS Sensor Plug Connections And Board

Insert USIS sensors (1) in direction of arrow into frame (2).

NOTE: USIS sensors (1) are used only when anti-theft alarm system is fitted.

Switch
Fig. 265: Inserting USIS Sensors Into Frame

Clip frame (1) into cover (2).

Switch
Fig. 266: Identifying Frame With Cover

Turn board (1) over in direction of arrow and connect plug connection (2) to board (1).

Switch
Fig. 267: Turning Board

Version from 08/2009

Rotate PCB (1) in direction of arrow.

Wind cable (2) in direction of arrow and connect with PCB (1).

Switch
Fig. 268: Rotating PCB

Clip board (1) onto frame (2).

Installation note

Make sure guide (3) is correctly seated in frame (2).

Switch
Fig. 269: Identifying Board On Frame And Guide

Installation note

If anti-theft alarm system is fitted, make sure USIS sensor lead (1) is correctly seated in retaining tabs (2) on frame (3).

Switch
Fig. 270: Identifying USIS Sensor Lead And Retaining Tabs On Frame

Clip light pressed screen (1) into light unit (2).

Installation note: Make sure pin (3) is correctly seated on board (4).

Switch
Fig. 271: Identifying Light Pressed Screen On Light Unit And Pins On Board

Install bulbs (1) in light pressed screen (2).

Installation note: Note BULB TYPE.

Switch
Fig. 272: Identifying Bulbs On Light Pressed Screen

Screw down base (1) to roof switch cluster (2).

Switch
Fig. 273: Identifying Roof Switch Cluster With Base

  • Carry out VEHICLE PROGRAMMING/ENCODING

REPLACING SWITCH COMBINATION FOR SEAT ADJUSTMENT (COMFORT SEAT IN REAR COMPARTMENT)

Notes

IMPORTANT: Read and comply with notes on protection against electrostatic damage (ESD PROTECTION).

Carefully lever out cover (1) with special tool 00 9 317 and release screws underneath.

Switch
Fig. 274: Removing Cover Using Special Tool (00 9 317)

Carefully raise center armrest decorative trim (1) in direction of arrow.

Lift switch combination for seat adjustment (2) in direction of arrow out of side guide (3) and feed out.

Disconnect plug connection behind.

Switch
Fig. 275: Lifting Switch Combination For Seat Adjustment Out Of Side Guide

Installation

Make sure switch combination for seat adjustment (2) is correctly seated in side guide (3).

REPLACING SWITCH FOR EXTERIOR MIRROR

Operation is described in:

Removing POWER WINDOW SWITCH (DRIVER'S SIDE)

    READ NEXT:

     Horn

    REMOVING AND INSTALLING/REPLACING LEFT FANFARE HORN Necessary preliminary work Remove FRONT LEFT WHEEL ARCH COVER On vehicles with auxiliary heaters as equipment specification, remove BUMPER TRIM

     Insert Holder

    REMOVING AND INSTALLING/REPLACING 12V SOCKET IN CENTER ARMREST STORAGE COMPARTMENT Necessary preliminary tasks REMOVE CENTRE ARMREST STORAGE COMPARTMENT Remove 12V socket with special tool 61 0 250

     Control Units, Modules

    SEE MORE:

     Functional Principal

    Lane Departure Warning The lane departure warning causes the steering wheel to vibrate to warn the driver that the vehicle is threatening to leave the current lane without driver intending it to do so. The prerequisite for this function to work is the presence of road or lane markings that can be

     First-aid kit

    General information Some of the articles have a limited service life. Check the expiration dates of the contents regularly and replace any expired items promptly. Storage The first-aid kit is located in the left storage compartment of the cargo area. BMW Roadside Assistance Concept Contact the BMW

    © 2019-2024 Copyright www.bmw7g11.com