BMW 7 Owners & Service Manuals
BMW 7 Series (G11/G12) 2015-2022 Owners Manual / Controls / Climate control / Stationary climate control through Remote Engine Start- Climatization for the requested departure time

BMW 7 Series: Stationary climate control through Remote Engine Start- Climatization for the requested departure time

General information

Scheduled departure times can be set up in the system to ensure a comfortable interior temperature in the vehicle at the time of departure.

  • One-time departure time: the time of the scheduled departure can be set.

    The system is switched on once.

  • Departure time with weekday: time and day of the week of the scheduled departure can be set.

The departure time is preselected in two steps:

  • Set departure times.
  • Activate departure times.

The climate control function will start approximately 10 minutes before the set departure time and continue for approximately 5 more minutes after the departure time.

A minimum of 10 minutes should pass between setting/activating the departure time and the planned departure time to allow a sufficient period of time for the climate control.

For reasons of safety, the system can only be switched on once. The system will be available again as soon as the drive-ready state is activated and deactivated again.

Observe the information about the intended use of the vehicle.

Additional information: For Your Own Safety

Setting the departure time

Via iDrive

  1. "CAR"
  2. "Settings"
  3. "Climate control"
  4. "Preconditioning/ventilation"
  5. Select the desired departure time.
  6.  Set the departure time.
  7. Select day of the week, if needed.

Via BMW display key

  1. Switch on the display of the BMW display key.
  2. "Preconditioning setting"
  3. Tap on the symbol.

  4. Select the desired departure time.
  5. Set the departure time.
  6. Select day of the week, if needed.
  7.  "OK"

Activating the departure time

Functional requirement

If a requested departure time is to influence the switching on of the system, the respective departure time must be activated first.

Via iDrive

  1. "CAR"
  2. "Settings"
  3. "Climate control"
  4. "Preconditioning/ventilation"
  5. Activate the desired departure time.

The symbol on the automatic
climate control signals an activated departure time

Via BMW display key

  1. Switch on the display of the BMW display key.
  2. "Preconditioning setting"
  3. Tap on the symbol.

  4.  Activating the desired departure time: Tap on the symbol.


    The symbol on the automatic
    climate control signals an activated departure time.

Display in the instrument cluster

Symbol /Description

The engine runs for the purpose
of operating the stationary climate control. The vehicle is not ready to drive.

    READ NEXT:

     Ambient air package

    Concept The Ambient Air Package can be used to clean and scent the interior air with high-quality fragrances. Ionization is used to clean the air from suspended particles. Together with the selected

     Ambient air package- Inserting fragrance cartridges

    The fragrance cartridges are located in the glove compartment. Open the glove compartment. Front passenger side glove compartment Press on the bottom of the cartridge holder. The cartridge holder

     Interior equipment

    SEE MORE:

     Water Pump With Drive

    Removing And Installing/Renewing Coolant Pump (N63) WARNING: Risk of scalding! Only perform this work after engine has cooled down. Recycling Catch and dispose of drained coolant in a suitable collecting vessel. Observe country-specific waste disposal regulations. IMPORTANT: If a coolant pump which

     Fuel Delivery, Sensor For Display

    REMOVING AND INSTALLING OR REPLACING CARBON CANISTER Necessary preliminary tasks Remove rear right WHEEL ARCH COVER Unlock quick-release fasteners (1) and disconnect vent lines. Release screws (2) and swing out carbon canister (3). Installation: Tightening torque 16 13 1AZ. Fig. 32: Identifyin

    © 2019-2025 Copyright www.bmw7g11.com