BMW 7 Owners & Service Manuals

BMW 7 Series: Mandrel

Minimum set: Mechanical tools Mandrel MW

Note: (drift) For driving radial shaft seal onto drive flange.

Storage Location

B26

SI number

01 09 09 (532)

Rear Axle
Fig. 25: Identifying Mandrel (330150)

Mandrel MW

Replaced by: 0491891

Note: (Drift) Replaced by 31 2 040.(0 491 891)

Mandrel MW

Replaced by: 0492338

Note: (Drift) For radial seal on output flange - Replaced by 33 3 420.(0 492 338)

Rear Axle
Fig. 26: Identifying Mandrel (331210)

Minimum set: Mechanical tools Mandrel MW

Note: For driving the radial shaft seal of the output shaft into the rear axle final drive.

Rear axle final drive: 188

Storage Location

C21

SI number

01 22 06 (307)

Rear Axle
Fig. 27: Identifying Mandrel (335130)

Mandrel MW

Replaced by: 0492338

Note: (Drift) For fitting the radial sealing ring, right-hand output end/Replaced by 33 3 420.(0 492 338)

Rear Axle
Fig. 28: Identifying Mandrel (333380)

Minimum set: Mechanical tools Mandrel MW

Note: For driving in shaft seal on drive shaft.

Storage Location

A16

SI number

01 21 06 (300)

Rear Axle
Fig. 29: Identifying Mandrel (335080)

Mandrel MW

Replaced by: 0492339

Note: (Drift) For driving the radial seal into the output flange with flange diameter 38 mm - Replaced by 33 3 430.(0 492 339)

Rear Axle
Fig. 30: Identifying Mandrel (331170)

MOUNTING ADAPTER

Mounting adapter

Note: Locator for E85 Z4 M. SI 01 10 06 (264)

SI number

01 10 06 264

Rear Axle
Fig. 31: Identifying Mounting Adapter (33 4 426)

    READ NEXT:

     Open-End Wrench

    Minimum set: Mechanical tools Open-end wrench MW Note: Open-end spanner SW50 with retaining clip For releasing and tightening down the insert nuts for the screw connection of the propeller shaft on t

     Spindle

    Spindle MW Note: (Spindle with nut) For device 33 0 000, for removing and installing rubber mounts of rear axle support mounting. Storage Location C25 B25 SI number 01 18 08 (482) Consisting of: Fig

     Tool

    TOOL Tool MW Note: (Press-out/-in tool set) For pressing the rubber mount out of and into the control arm special tools 33 3 202 and 33 3 203 for E87 and E90 Storage Location B32 SI number 01 05 90 (

    SEE MORE:

     Electrical Steering Column Adjustment Normalization

    NOTE: Normalization must be carried out after the following work: Removal or replacement of control panel in heater-A/C system or of steering column Repair work to electric steering column adjustment Coding/programming of IHKA control unit Normalization of electric steering column adjustment i

     Overview Of Adhesive Cartridge Guns

    Adhesive gun 83 19 2 149 522 Usable for adhesives K4, K5a. Including insert 1:1 and 2:1. Fig. 28: Identifying Adhesive Gun (83 19 2 149 522) Adhesive gun 81 49 0 443 166 Usable for adhesive K3. Fig. 29: Identifying Adhesive Gun (81 49 0 443 166) Adhesive cartridge gun 81 49 2 159 881/883 Usable fo

    © 2019-2024 Copyright www.bmw7g11.com